Hey all,

For those who own a SV08, what kind of mods did you install on your printer?

Secondarily, does anyone have a multi toolhead mod? I’m not quite sure whether I should go with the INDX way or use OG toolheads.

Happy to hear your thoughts!

  • emrsmsrli@lemmy.worldOPEnglish
    2·
    11 days ago

    that’s great, thanks for the reply! i’d love to see your enclosure solution. i’ve only recently started working with more advanced materials and ASA/ABS is next on my list

    • AnyOldName3@lemmy.worldEnglish
      2·
      10 days ago

      I’ve got https://www.printables.com/model/959792-sovol-sv08-enclousure on the top and back (as they’re the panels that didn’t fail, although the top’s a bit droopy as I printed it in black, then put the printer outside on a sunny day so the fumes would blow away when doing some ABS printing before I’d set up extraction for indoors). If you’re printing that yourself, I’d recommend making the screw holes bigger, as the STL has them the right size to tap an M3 thread into instead of the right size to pass an M3 screw through.

      I had some spare insulation foam that fit in the gaps in the lid, and lined the rest with a roll of reflective-mylar-backed polystyrene insulation I had lying around, so that helps keep more heat in.

      When the panels that failed failed, I just bought some 4mm plywood for £4, drew and cut out some rectangles the same size as the STEP files Sovol released for the printer said they’d needed to be, and drilled some holes where the CAD file said the screws needed to go (plus an extra bonus hole in the wrong place by accident) and a slit to pass the reverse Bowden tube and filament sensor wire through.

      The doors are https://www.printables.com/model/946451-sovol-sv08-doors-jls-mod-v2, which I paid a local man with a laser cutter £30 ish to do in 4mm acrylic.

      I also printed a top-hat in ABS once I’d got the enclosure reliably hot enough to have ABS not just warp itself to oblivion. I wasn’t going to risk wasting time doing it in PLA after half the enclosure panels I’d made with it had failed. https://www.printables.com/model/1083936-closed-sv08-hat-w-heatset-insert-support I added some extra holes for heat-set inserts for an air filter, although in the end, I realised it was better to just extract the fumes as some would inevitably leak out the enclosure.

      To extract the fumes, I got some wood and made a panel I could fit over a window to attach an air duct, then I got a cheap mini greenhouse and cut it up so it fit over the whole printer so I could connect the other end of the duct and a fan. If the duct fan is always sucking air out of the tent, then fumes that escape the enclosure don’t go into the room, but the hot air in the enclosure mostly stays in the enclosure, so I don’t lose heat like I would if extracting directly from the printer.

      • emrsmsrli@lemmy.worldOPEnglish
        2·
        9 days ago

        wow thanks for the detailed answer. I’ll check it out! I plan on an internal air circulation with active carbon and hepa, hopefully it’ll be sufficient

        • AnyOldName3@lemmy.worldEnglish
          2·
          8 days ago

          I made this filter https://www.printables.com/model/1276996-recirculating-carbon-hepa-filter-for-sv08 and attach it to heat-set inserts in the top hat I made rather than to the mounting holes for the spool holder (as I’ve got the spool holder attached there). It’s definitely filtering, but even with a 12V fan being run at 24V, it’s not enough to make the air in the printer fully unsmelly, and not enough to stop the smelly air that leaks making the whole room smell of molten ABS.

          There are higher-performance filters like the various Nevermore designs, but they’re more of a pain to print and more complicated than they need to be, and don’t fit anywhere in an SV08 without getting in the way of something and sacrificing print volume.