

As an OpenSuse user, should I look for alternatives? I do like OpenSuse as it is now…


As an OpenSuse user, should I look for alternatives? I do like OpenSuse as it is now…
Vertical holes are much narrower than horizontal ones even though they have the same size in the model. This is because plastic flows inward and also because it doesn’t draw perfect circles.
A good slicer can compensate for that by making vertical holes a bit wider.
Indeed preflight looks interesting. I will likely move from prusa to orca but some of the features of preflight look really nice.


Indeed it was, my PA setting was 10x too high.


Ah, I see the problem. I messed up the calculation, instead of .072 PA I used 0.72. The part that got printed looked quite bad as well so that explains a lot. I’ve entered more normal values and now it looks much better.
Thanks!


I have a direct drive. Indeed I want the runout length as short as is reasonable.


Actually this isn’t exactly my setup. I forgot the pin number and copied the example piece instead.


Can’t argue with that.


How is the fire safety?
My concern with IKEA enclosures is that they’re made of mostly cardboard and anything catching fire will easily spread around.


No it doesn’t get that hot. I’ve also designed ventilation channels into it so the hot air from the hotend goes out the top.
If the hotend cooling fans fail then it does get quite toasty but in normal use they can handle it.
Also it’s made of ABS.


Well well well, you have something to xiaomi.
A thermistor is just a resistor that changes resistance based on temperature. All you need to do is hook up a multimeter and wiggle the cable. If the resistance is consistent then it’s fine physically.
Most hotends have an NTC 10k so at 25 degrees C the resistance is 10K ohms. The higher the temperature the lower the resistance will be.
If you have a different type it will need to be configured in your firmware as well.
What helped me a lot is to find a model (STEP file) of the printer you have and import that into whatever CAD program you prefer.
I found FreeCAD to be by far the most pleasant program to use. It is not even close. No accounts, no cloud , no subscriptions, no “AI”. None of that modern SAAS bullshit or enshittification. FreeCAD updates make it better instead of worse.
It is definitely not perfect but it is free and open source and the developers have done a really good job with this.
Anyway, once you’ve imported the model into CAD it becomes much much easier to design parts around it. You can find many models on sites like grabcad.com but you will need to make an account to download (urgh). Just fill in some random BS on a throwaway account and you’re fine though.
Ah I see the picture in the OP still has the old version. Indeed that is true and therefore I redesigned the YX joints to make nice 90 degree angles with the belts. In that version I made the idlers sit on the same screws that held the YX joint to the rail slider.

The belts did not make 90 degree paths from the stepper motor towers and also not from the YX joints to the toolhead. This caused uneven tension that was most noticable when the toolhead got close to the YX joint or when the YX joint got close to the stepper tower. The belt angle would change based on the location of either object and that changed the amount of force needed to pull it.
I’ve learned that the belts ideally make 90 degree angles when pulling something. One belt path comes out the left side of the idler and the other comes out of the right side. At the toolhead you insert the belt from either the left side or the right side to make the belt as straight as possible.


A few years ago I used glass beds. Not fancy ones, I got a large cheap mirror from the hardware store and a glass cutter. Both combined were cheaper than a single bed meant for 3D printing and for PLA they lasted multiple months. PEI is just more practical since it won´t randomly break and is flexible making part removal very easy.
I ruined it by trying to print PETG on it without any adhesion layer in between. It took out a nice chunk of glass from the center.


That is…pretty minor compared to some of the catastrophic mistakes here haha.


I thought of that a well. The resin will likely not get everywhere. The idea was saving costs as resin is kinda expensive.


I think it’s cheaper than using resin haha.


I… may have short circuited the hotend fan mosfet and broke it. I just let them run at full speed since then.
I mean, as disgusting as cheating is, this is kinda mild compared to other billionaire ceos which are blatant neo nazis or epstein customers.